StS_spencer
I am running an Intel platform still no luck on flashing the bios. cmd prompt closes in a split of a second without any input needed. doubled checked the switch on the card its on master and the update is launched with admin rights.

Any antivirus/defender etc running? These may stop the prog from running

Rain_1
 

ilyama

Xavi91
Can you guys share the new curve please?

I'm asking to everyone with the new bios and some evga guys, no answer at all, I begin to think it's a legend 

How would one provide the new curve? I don't usually run the Precision software - I think it's bloated and not intuitive. I just want a videocard that works and don't care about overclocking, so I just install regular drivers and that's about it.
 
On my 08G-P4-6276-KR with Bios 86.04.50.00.72, these are the curves being shown on precision:
 
Quiet:
 
 
Aggressive:

 
 
 
Is what what you guys want?

 
IF you make vbios change and go right after in evga precision, it will show you the active curve on your graphic card no ?

The people linking those curves: Those are PrecisionOCX Built in custom fan profiles for curstom, quiet and aggresive. The automatic fan curve is not shown! Only an engineer @ evga can show those, or you have to manually monitor temps and fan speeds to find out the curve.

just restarted the computer twice now it worked ;D dont know where the problem was.
 

EVGA_JacobF

Handroxrj
Updated the bios of my 08G-P4-6276-KR - EVGA GeForce GTX 1070 FTW ACX 3.0 utilzando the bios available for this link in the main post - 08G-P4-6276-KR - EVGA GeForce GTX 1070 FTW ACX 3.0 - Primary BIOS (86.04.3b.00.72), it happens that after the update the numbering of the bios that appears in the GPU-Z is the Primary BIOS was made (86.04.50.00.72) and not of Primary BIOS (86.04.3b.00.72) this correct it?

50.00.72 is correct.

Luta Wicasa
 
 
Yes...that was a typo and is now corrected.

Thx guys

Xfade81
The people linking those curves: Those are PrecisionOCX Built in custom fan profiles for curstom, quiet and aggresive. The automatic fan curve is not shown! Only an engineer @ evga can show those, or you have to manually monitor temps and fan speeds to find out the curve.

Ok, this is good information. Everybody somebody said "I managed to flash my videocard", somebody would immediately ask "can you share the new curves?". I imagined that the actual videocard's curve (the one stored in the bios) is not accessible by users - which is why I was confused.

StS_spencer
I am running an Intel platform still no luck on flashing the bios. cmd prompt closes in a split of a second without any input needed. doubled checked the switch on the card its on master and the update is launched with admin rights.

Can you upload a screenshot of GPUZ?

Xfade81
The people linking those curves: Those are PrecisionOCX Built in custom fan profiles for curstom, quiet and aggresive. The automatic fan curve is not shown! Only an engineer @ evga can show those, or you have to manually monitor temps and fan speeds to find out the curve.

Ok, I didn't know that...

So I hope that a member of EVGA will answer me positively... it's not a lot to ask I think 

jacob no further help needed just did a restart of the computer twice with full shutdown, now it worked. dont know where the problem was, maybe it was prec. x oc that was blocking it.
 

StS_spencer
jacob no further help needed just did a restart of the computer twice with full shutdown, now it worked. dont know where the problem was, maybe it was prec. x oc that was blocking it.
 

Woooo! Good deal.