Make sure you have "Power Target" set to focus, and set to 120%, rather than Temperature(but I would also set Temp Target to 92C). Make sure V-Sync is disabled on your panel, and finally make sure your "Target Frame-rate" is set to "off" under PrecisonX control panel. Some games, especially newer games have newer settings under Video settings such as "Force Resolution" and "Dynamic Graphic Settings" If you are going to use the Dynamic settings, make sure you set it to "High" or "Ultra", as a Medium setting will have poor impact on your fps, for me and my 1080 F|E I had to "unlock" several graphic settings to get the most out of my card. I was getting low fps until I set all my graphic settings to Ultra under "Dynamic Control", and other settings such as Unlock Frame-Rate" turn off "Force Resolution".

Scarlet-Tech
Post a screen shot of GPU-Z sensor tab with the card under load, at idle, and also post a screen shot of the GPU-Z main screen. Make sure your pci lanes are not running x1 or lower than x8 or x16 pci 3.0

Attachet I leave my GPU-Z screenshots

Sean1976
Make sure you have "Power Target" set to focus, and set to 120%, rather than Temperature(but I would also set Temp Target to 92C). Make sure V-Sync is disabled on your panel, and finally make sure your "Target Frame-rate" is set to "off" under PrecisonX control panel. Some games, especially newer games have newer settings under Video settings such as "Force Resolution" and "Dynamic Graphic Settings" If you are going to use the Dynamic settings, make sure you set it to "High" or "Ultra", as a Medium setting will have poor impact on your fps, for me and my 1080 F|E I had to "unlock" several graphic settings to get the most out of my card. I was getting low fps until I set all my graphic settings to Ultra under "Dynamic Control", and other settings such as Unlock Frame-Rate" turn off "Force Resolution".

Thank you. All your recommendations I've checked and everything is as you tell me. Except Power target, only I can set a maximum of 112%

You need to add spaces to your link address as you can't post links until after your 11th post (assuming that is what you did as nothing appears).

jm_loli

Sean1976
Make sure you have "Power Target" set to focus, and set to 120%, rather than Temperature(but I would also set Temp Target to 92C). Make sure V-Sync is disabled on your panel, and finally make sure your "Target Frame-rate" is set to "off" under PrecisonX control panel. Some games, especially newer games have newer settings under Video settings such as "Force Resolution" and "Dynamic Graphic Settings" If you are going to use the Dynamic settings, make sure you set it to "High" or "Ultra", as a Medium setting will have poor impact on your fps, for me and my 1080 F|E I had to "unlock" several graphic settings to get the most out of my card. I was getting low fps until I set all my graphic settings to Ultra under "Dynamic Control", and other settings such as Unlock Frame-Rate" turn off "Force Resolution".

Thank you. All your recommendations I've checked and everything is as you tell me. Except Power target, only I can set a maximum of 112%

Your temperatures look good, all I can see on the GPU-Z shots is that you are TDP/voltage limited (VRel). But that should not result in below 99% GPU utilization.
 
Are you running anything in the background that takes a lot of CPU? Stuff like FRAPS, or perhaps even GFE with shadowplay.

Vayra86

jm_loli

Sean1976
Make sure you have "Power Target" set to focus, and set to 120%, rather than Temperature(but I would also set Temp Target to 92C). Make sure V-Sync is disabled on your panel, and finally make sure your "Target Frame-rate" is set to "off" under PrecisonX control panel. Some games, especially newer games have newer settings under Video settings such as "Force Resolution" and "Dynamic Graphic Settings" If you are going to use the Dynamic settings, make sure you set it to "High" or "Ultra", as a Medium setting will have poor impact on your fps, for me and my 1080 F|E I had to "unlock" several graphic settings to get the most out of my card. I was getting low fps until I set all my graphic settings to Ultra under "Dynamic Control", and other settings such as Unlock Frame-Rate" turn off "Force Resolution".

Thank you. All your recommendations I've checked and everything is as you tell me. Except Power target, only I can set a maximum of 112%

Your temperatures look good, all I can see on the GPU-Z shots is that you are TDP/voltage limited (VRel). But that should not result in below 99% GPU utilization.
 
Are you running anything in the background that takes a lot of CPU? Stuff like FRAPS, or perhaps even GFE with shadowplay.

Im running GFE with shadowplay in the background, but I have another disc with a clean windows 10 installation with no GFE installed, and I cant see any diference in the GPU load. I don't know what else to do.  

Make sure your windows power options are set to high performance.

Sajin
Make sure your windows power options are set to high performance.

 
Cheked, and it was established to high performance, same in the nvidia control panel 
 
Any other sugestions?
If I make a slight overclock could improve performance?

overclock won't help.
 
You should try:
Use of DDU to uninstall the Nvidia driver and install again.
And update your MotherBoard BIOS (there is a lot of board manufactures that release bios update specifically for pascal GPUs)
 
If you run haven benchmark, does our GPU achieve 99% ?

dzernesto
overclock won't help.
 
You should try:
Use of DDU to uninstall the Nvidia driver and install again.
And update your MotherBoard BIOS (there is a lot of board manufactures that release bios update specifically for pascal GPUs)
 
If you run haven benchmark, does our GPU achieve 99% ?

+1