yea my peak was 84 but only in one core the rest was 81,81,79

here is a pic sorry  as I have know idea how to make it bigger

well I had to raise the IOH Vcore up one notch as I kept getting problem with my video card while playing game and once I did that I think it fixed my video problem  I ran linX agian and I can't belive its not stable agian **** I ran it 50 test  last night and it passed and now I raise the IOH Vcore and it fails on test 23 I am going crazy with this I have no idea what is going on can someone plz help me I also want to know what do I set the  Memory Low Gap ( Auto ) to  as I read it has to do to pci express and wondering if it will help my video card also what do I set Maximum Payload Size ( 128  ) to 2048 or 128 or 4096 ? will it help my video card ? plz help I going crazy with this and linx is ethier buged or is not reliable plz help

well sometimes I get an error in LinX other times I get BSOD and that re testing the same settings 

My NB os 50c to 53c in the bios and yea my games run alot better now I will run prime95 blend test overnight now if I do get an error what do I change?


Mother Board ( EVGA X58 Classified E-760 )                                                         
Bios ( S61J )                                                                                                       
CPU ( 960 DO) 
CPU Cooler ( Prolimatech Mega Shadow )  
Memory ( Corsair Dominator GT 1600 7 7 7 20 )  
PSU ( Thermaltake 1000w)  
GPU ( EVGA GTX 295 Co-op )  
Drivers ( 195.81 )                                                                                                    
Operating System ( Windows 7  x64 Ultimate )  

Frequency Control  
CPU Clock Ratio ( 24x )                                                                                        
CPU Host Frequency (Mhz) ( 169 )                                                                        
MCH Strap ( Auto )  
CPU Uncore Frequency (Mhz) ( Auto )                                                  
CPU Clock Skew ( 0 ps )  
Spread Spectrum ( Disabled )  
PCIE Frequency (Mhz) ( 101 ) 

Memory Feature          
Memory Speed ( Standard )  
Memory Control Setting ( Enabled )  
Memory Frequency ( 1333 / 2:10 )                                                                  
Channel Interleave Setting ( 6 Way )  
Rank Interleave Setting ( 4 Way )  
Memory Low Gap ( Auto )  
tCL Setting ( 7 )  
tRCD Setting ( 7 )  
tRP Setting ( 7 )  
tRAS Setting ( 20 )  
tRFC Setting ( Auto )  
Command Rate ( 1T )  
Voltage Control  
EVGA VDroop Control ( With VDroop )  
CPU VCore ( 1.41875v )                                                                                                  
CPU VTT Voltage ( +125mv )  
CPU PLL VCore ( 1.500v )  
**IOH PLL VCore ( 1.500v )   
DIMM Voltage ( 1.65 )  
DIMM DQ Vref ( Auto) (+0mV)  
QPI PLL VCore ( 1.3 )  
IOH VCore ( 1.150 )  
IOH/ICH I/O Voltage ( 1.525 )  
**VTT PWM Frequency ( 370 KHZ )  
**CPU PWM Frequency ( 940 KHZ )  
**CPU Impedance ( Less )  
**QPI Signal Compensation ( Less )  
CPU Feature  
Intel SpeedStep ( Disabled )  
Turbo Mode Function ( Enabled )  
CxE Function ( Disabled )  
Execute Disable Bit ( Enabled )  
Virtualization Technology ( Disabled )  
Intel HT Technology ( Enabled )  
Active Processor Cores ( All )  
QPI Control Settings ( Enabled )  
QPI Link Fast Mode ( Enabled )  
QPI Frequency Selection ( 4.800 GT/s )  
OC Recovery ( Enabled )  

PnP/PCI     PCI Express  
Maximum Payload Size ( 2048  )  
   
Power Management Setup  
ACPI Suspend Type ( S3 )     
HPET Support ( Enabled )       
HPET Mode ( 64-bit )   

so If I get an error that would mean I can't run the memory at that speed huh?

You'd probably get even better performance by going to 2:8 and then maybe trying tighter timings......

ok let me at least try to run prime for a while to see if its stable then I will do what u say lower my ram to 2:8 with tighter timing

now what timing would I set it to with  2:8 and what other setting would I need to change thnxs for the help ?

You will have to experiment with timings but think you could do 6-6-6 with 2:8 or perhaps just up the voltage a bit more on ram and keep it at 2:10.

Thats not what he said, slow down and read what people are saying.....LOL

If you have no luck increasing the vdimm, turn it back to 2:8. This will lower you uncore frequency down to x16 (make sure its set) which will allow you to lower your VTT.  Since your ram is 1600mhz 7-7-7-20 @ 1.65v, I would set it to 2:8 @  6-6-6-18 @ 1.65v

Check this out. My ram is 2000mhz 8-8-8-24 @ 1.65v

I can do 1733mhz 7-7-7-18 @ 1.63v perfectly stable. If I go to 6-6-6-18 I need 1.72 vdimm. 6-6-6-18 on my ram is like setting 5-5-5-15 on yours. Hope that gives you an idea.

ok got it now my question I know there is memtest+86 to test ram is what u tested your ram with to make sure its stable or you  used prime95 blend test?  

so from what I understand running my memory with tighter timing than running it at a higher clock is faster correct?

memtest+86 is just that it will test your memory, but I do not think it tests for stability in your system working with cpu.(someone please correct me if I am wrong) it is not a stress test.

DENTNU

so from what I understand running my memory with tighter timing than running it at a higher clock is faster correct?

its different, i forget exactly, maybe someone else can clarify me, but the higher speed has an advantage one way, while lower timings has an advantage another way. One has better latencies and one has better write speed... something like that. I am not sure though, someone will have to clarify this better than I can.