DENTNU

I almost had it stable at 7-7-7-20 and 2:10 divider with the vtt at +125 it passed 15 tests but when it hit 16 I got a BSOD you think if I raise my dimm volt to 1.66 it will get stable and more importantly is it safe to run with vdimm at 1.66 as I heard anything above 1.65 could damage the memory and the cpu let me know I was so close yet so far lol 

Raise the Vtt 1 notch

give me min and I will test it agian but last time I tested it it gave me BSOD on the first test 

Ok first thig is I redid my TIM on the cpu and took off the memory fan and my temps drop a few degrees. next I got it stable with 2:10 divider and +125 vtt and vdimm at 1.66 now my question is it safe to run 24/7 with vdimm at 1.66? 


here are my new settings and a pic thanks 

Mother Board ( EVGA X58 Classified E-760 )                                                        
Bios ( S61J )                                                                                                      
CPU ( 960 DO)
CPU Cooler ( Prolimatech Mega Shadow ) 
Memory ( Corsair Dominator GT 1600 7 7 7 20 ) 
PSU ( Thermaltake 1000w) 
GPU ( EVGA GTX 295 Co-op ) 
Drivers ( 195.81 )                                                                                                   
Operating System ( Windows 7  x64 Ultimate ) 

Frequency Control 
CPU Clock Ratio ( 24x )                                                                                       
CPU Host Frequency (Mhz) ( 169 )                                                                       
MCH Strap ( Auto ) 
CPU Uncore Frequency (Mhz) ( Auto )                                                 
CPU Clock Skew ( 0 ps ) 
Spread Spectrum ( Disabled ) 
PCIE Frequency (Mhz) ( 101 )

Memory Feature         
Memory Speed ( Standard ) 
Memory Control Setting ( Enabled ) 
Memory Frequency ( 1333 / 2:10 )                                                                 
Channel Interleave Setting ( 6 Way ) 
Rank Interleave Setting ( 4 Way ) 
Memory Low Gap ( Auto ) 
tCL Setting ( 7 ) 
tRCD Setting ( 7 ) 
tRP Setting ( 7 ) 
tRAS Setting ( 20 ) 
tRFC Setting ( Auto ) 
Command Rate ( 1T ) 
Voltage Control 
EVGA VDroop Control ( With VDroop ) 
CPU VCore ( 1.41250v )                                                                                                 
CPU VTT Voltage ( +125mv ) 
CPU PLL VCore ( 1.500v ) 
**IOH PLL VCore ( 1.500v )  
DIMM Voltage ( 1.66 ) 
DIMM DQ Vref ( Auto) (+0mV) 
QPI PLL VCore ( 1.3 ) 
IOH VCore ( 1.150 ) 
IOH/ICH I/O Voltage ( 1.525 ) 
**VTT PWM Frequency ( 370 KHZ ) 
**CPU PWM Frequency ( 940 KHZ ) 
**CPU Impedance ( Less ) 
**QPI Signal Compensation ( Less ) 
CPU Feature 
Intel SpeedStep ( Disabled ) 
Turbo Mode Function ( Enabled ) 
CxE Function ( Disabled ) 
Execute Disable Bit ( Enabled ) 
Virtualization Technology ( Disabled ) 
Intel HT Technology ( Enabled ) 
Active Processor Cores ( All ) 
QPI Control Settings ( Enabled ) 
QPI Link Fast Mode ( Enabled ) 
QPI Frequency Selection ( 4.800 GT/s ) 
OC Recovery ( Enabled ) 

PnP/PCI     PCI Express 
Maximum Payload Size ( 2048  ) 
  
Power Management Setup 
ACPI Suspend Type ( S3 )    
HPET Support ( Enabled )      
HPET Mode ( 64-bit )  

Yes it is safe. As long as Vdimm and Vtt are with in .5 volts you are good to go. That means if Vtt is at 1.325 then you should be safe all the way up to 1.825 on Vdimm. Do not go that high on vdimm though not necessary. You should be safe 24/7 What were your max temps? Pic to small to see. Edit: see it now. Great job.

hey thanks for all your help I know I could not have done it without your help  I clicked your link but it took me to just the forum main menu can you fix it thanks 

ok thanks

Pull the cpu out and look at the numbers etched on the spreader. The very bottom set of numbers will tell you the batch #.

one last question do u let windows 7 manage page file or do u set it yourself? 

wow nice overclock I like the way u fine tune it all 

hey man guess what Iiy looks like I am not 100% stable after all I started to play some games and they start to freeze randomly and studder one time it even kicked me out of a game back yo the desktop so I started to trouble shoot I reinstalled the video drivers same thing then I decide to rerun linx and see if it was still stable and guess what I got an error on the second test I mean come on it pass 20 test yesterday and now its not stable **** oh well back to the trial and error mission any suggestions?

Yes. Your uncore was upped a lot your memory is not over clocked that much. but perhaps using a 295 go-op might need to up ioh a notch.

which one do i raise ?

IOH VCore ( 1.150 )  
IOH/ICH I/O Voltage ( 1.525 )

u might think I am crazy but u think I would need to riase the vcore another notch with my ram clocked that high?

Maybe not but the ioh is what the video uses.

Like we have said before if you are comfortable with the temps then your good especially if you are below 85C in Linx.