EVGA

custom cable question

Author
Post
Essentials Only Full Version
seta8967
FTW Member
  • Total Posts : 1813
  • Reward points : 0
  • Joined: 2010/03/03 05:18:45
  • Status: offline
  • Ribbons : 2
2015/07/07 16:39:11 (permalink)
I am trying to make custom cable for my 1000p2 and 1600t2. Are the wires cable both female ends on both sides? Is there a 24pin connector that doesn't have the split 20+4, that I can buy? Unfortunately I don't have my psu's with me right now so difficult to figure out what they are via pictures. Just want to make sure I buy the correct items.
#1

3 Replies Related Threads
    Pgcmoore
    CLASSIFIED Member
    • Total Posts : 2037
    • Reward points : 0
    • Joined: 2011/03/27 09:29:41
    • Location: Florida
    • Status: offline
    • Ribbons : 14
    Re: custom cable question 2015/07/07 18:37:13 (permalink)
    There female on both ends ,connectors and terminals however Evga's 24 pin connectors have 24 pin one end and a 10- 18 pin dual connector on the PSU side.
     
     

     With lots of doubles (2 into 1) quite a pita to make with 16-20 gauge IMO. Have you given the custom sleeved ones from evga a thought?
    http://www.evga.com/Produ...(Individually+Sleeved)
     
     
    I found these guys to have all the best tools and connectors , terminals of any, you can find the connectors ( they have the 10 and 18 pin ) and terminals you need here,
     
    http://mainframecustom.co...e-sleeving/connectors/
     
     
    I would recommend using female terminals with "long wings" if plan to crimp the sleeving, 
     
     
     
    http://mainframecustom.co...erminal-molex-5-count/
     
    post edited by Pgcmoore - 2015/07/07 20:41:58

       "This program has performed an illegal operation and will be shut down"    
                                  
                            My Affiliate Code is  05G-UGD-GZVU
     
    #2
    seta8967
    FTW Member
    • Total Posts : 1813
    • Reward points : 0
    • Joined: 2010/03/03 05:18:45
    • Status: offline
    • Ribbons : 2
    Re: custom cable question 2015/07/07 23:22:36 (permalink)
    Pgcmoore
    There female on both ends ,connectors and terminals however Evga's 24 pin connectors have 24 pin one end and a 10- 18 pin dual connector on the PSU side.
     
     

     With lots of doubles (2 into 1) quite a pita to make with 16-20 gauge IMO. Have you given the custom sleeved ones from evga a thought?
    http://www.evga.com/Produ...(Individually+Sleeved)
     
     
    I found these guys to have all the best tools and connectors , terminals of any, you can find the connectors ( they have the 10 and 18 pin ) and terminals you need here,
     
    http://mainframecustom.co...e-sleeving/connectors/
     
     
    I would recommend using female terminals with "long wings" if plan to crimp the sleeving, 
     
     
     
    http://mainframecustom.co...erminal-molex-5-count/
     




    I thought about using the EVGA ones and just cutting them to size. I was told that their cables used a very thin jacket and it sometimes showed through, also it is difficult to heatshrink and keep it on. I can't do the full length cable, as the motherboard cable need only be 10 inches long. I also don't think they have enough gpu cables. need 8 of them suckers.
     
    I think I can handle it from here. First time doing it so want it done right.
    #3
    Pgcmoore
    CLASSIFIED Member
    • Total Posts : 2037
    • Reward points : 0
    • Joined: 2011/03/27 09:29:41
    • Location: Florida
    • Status: offline
    • Ribbons : 14
    Re: custom cable question 2015/07/07 23:34:00 (permalink)
     
     
     
     
    I hear ya man, I decided to go heatshrinkless and takes some time,
     
    but good luck

    Attached Image(s)


       "This program has performed an illegal operation and will be shut down"    
                                  
                            My Affiliate Code is  05G-UGD-GZVU
     
    #4
    Jump to:
  • Back to Mobile