it completed it in 133 seconds and max temp was around 73 C

Yeah it did..Core0: 75c Core1:75C Core2:72C Core3:72c I didnt get SPP or MCP Max temps but right now they are at 51C and 59C respectivly at idle

This time i got an error starting the 5th pass saying my system is not stable. SPP 53C MCP 60C

I still failed when starting the 5th test

first 2 cores only by 1 degree everything else the same

i tried it at 1.45 and i got bsod with the Stop error 0x00000124

Man....I sure wish you would have let me know what's going on before you went offline....instead of just leaving me sitting here wondering for nearly 1/2 hr. Cya later.

OK...I sure can understand that....1.40v is where I wanted you to start at anyway...look at the template I posted. Good luck.

Sounds good. Now remember.....the object is to run it (vcore) at the lowest possible voltage and still be stable. If you take it way too low or too high...you will get a BSOD (as you found out). Adjust and test each (vcore) setting to figure out what that voltage is for your chip. Do not adjust any other voltages at this time. When it can pass the 5 standard every single time....go for 10 passes and see if it can still pass. Success, go for 15 passes then, 20. You want to not let the cores or SPP/MCP get over 80C. If any of them are consistantly reaching 80C then, try to find better cooling methods. Ambient room temp plays a key role...cool the room your rig is in as well as possible. Always keep an eye on your temps and never run IBT unattended. 
 
Keep me updated on your progress.

willem445

@ 1.45V (AIDA 64 Shows 1.312-1.366V) it passed 5 10 and 20 passes multiple times

And when you set 1.45v previously, you got a BSOD......OK.......well, good deal. Yep....the board has VDroop which, is why the BIOS set voltage is lower than that....some boards droop more than others. So, is that as low as you can set it and still consistantly pass the test? How do you like the way it runs Windows and your programs now?
 
 

You are very welcome...glad I was able to assist you Feel free to hollar at me if you need further assistance.

I may have been having problems becuase my system cant handle 8gig of memory. i just passed a test in IBT 2 or more notches below 1.45v with only one stick in. Im going to see if this solves my bad co 2 problem and i will also do some more stress testing.

I think your last post is in the wrong thread but anyways i am running rock solid with these settings.
 
BIOS Version: P10
**System **
CPU Freq, MHz:3600 GHZ 3.5
FSB Reference Clock, MHz: 1400
CPU Multiplier: [10X]
PCle x16-1 & 16-2, MHz:  [100]
PCle x16-3, MHz:  [100]
SPPc->MCP Ref Clock, MHz:  [200]
nForce SPP --> nForce MCP:   [5X]
nForce SPP c-- nForce MCP:   [5X]
 
**Spread Spectrum**
CPU Spread Spectrum: [Disabled]
HT Spread Spectrum: [Disabled]
PCle Spread Spectrurn(SPP): [Disabled]
PCle Spread Spectrurn(MCP): [Disabled]
SATA Spread Spectrum: [Disabled]
 
**FSB & Memorv Config**
FSB - Memory Clock Mode: [Unllinked]
FSB (QDR), MHz: [1400]
Actual FSB (QDR), MHz: 1400
x MEM (DDR),  MHz: 1600
Actual MEM (DDR), MHz: 1600
P1: [Enabled]
P2: [Enabled]
 

 
 [**System Voltages**
CPU Core: [1.425v]
CPU FSB: [1.35v]
Memory: [1.7v]
nForce SPP: [1.45v]
nForce MCP: [1.55v]
 
GTLVREF Lane 0: [AUTO] 
GTLVREF Lane 1: [AUTO]
GTLVREF Lane 2: [AUTO] 
GTLVREF Lane 3: [AUTO]
 
**CPU Configuration**
Limit CPUlD Maxval: Disabled
Intel Speedstep: Disabled
xPPM Mode: [Native]
CPU Thermal Control: [Disabled]
C1E Enhanced Halt State: [Disabled]
Execute Disable Bit: [Disabled]
Virtualization Technology: [Disabled]
CPU Core 0: [Enabled]
CPU Core 1: [Enabled]
CPU Core 2: [Enabled]
CPU Core 3: [Enabled]
 
It passed IBT many times and i ran Prime twice, once for 2 hours and another overnight each producing no errors.
I find it weird after i went from mult9 to 10 and dropped my cpu fsb down to 1400 i immediately stopped getting problems with my games, even using the GTX 460. All the games freezing and flickering and crashing went away.

No problem! I was wondering about that, i remember reading in that one thread that running ram higher than fsb is bad. Ill change it right away.

I am running memtest with 8 8 8 24 2t right now. After this whole ordeal with much frustration and head scratching i finally realized...i need a haircut! lol