Great job bud! hopefully people will be sharing soon :)

12 hours and counting:)

Here's mine, though I don't recommend it if your on Air.  you might get away with it on water. I'm using an SS phase change on it.

Mother Board ( EVGA Classified E-759- A1 )                                                       
Drivers(9.1.1.1025 )
Bios ( 49 )                                                                                                     
CPU ( Intel Core i7 980 XE )                   
CPU Cooler (300w Phase Change )
Memory (Corsair Dominator GT 6gbs  )
PSU ( Themaltake 1000w )
GPU ( EVGA 280 GTX x2 )
Drivers ( 197.13 )                                                                                                  
Operating System ( Windows 7 x64 )


Frequency Control
CPU Clock Ratio (25)                                                                                        
CPU Host Frequency (Mhz) (200 )                                                                      
CPU Frequency ( 5017MHz )
MCH Strap (auto )
CPU Uncore Frequency (Mhz) ( auto )                                                
CPU Clock Skew (disabled )
Spread Spectrum (disabled )
PCIE Frequency (Mhz) (102 ) If using SSDs, Check with your SSD manufacturer before raising above 100.  

Memory Feature        
Memory Speed (2000 )
Memory Control Setting ( 2:10)
Memory Frequency (auto )
Channel Interleave Setting (auto  )
Rank Interleave Setting (auto )
Memory Low Gap ( auto)
tCL Setting ( 7)
tRCD Setting (8 )
tRP Setting (7 )
tRAS Setting (20)
tRFC Setting (88 )
Command Rate (1T )


Voltage Control
EVGA VDroop Control (with  Vdroop )
CPU VCore (1.48v )                                                                                                
CPU VTT Voltage (1.35v )
CPU PLL VCore ( 1.65v)
**IOH PLL VCore (1.92v ) 
DIMM Voltage ( 1.65)
DIMM DQ Vref (+0 )
QPI PLL VCore (1.35v )
IOH VCore (1.35v )
IOH/ICH I/O Voltage (1.625v )
**BR04 ( NF200) Voltage (1.2v ) (only on E-759)
**VTT PWM Frequency (default )
**CPU PWM Frequency (800 )
**CPU Impedance (default )
**QPI Signal Compensation (default )
ICH VCore (1.35v )
*PWM Frequency (default )


CPU Feature
Intel SpeedStep ( disabled)
Turbo Mode Function (disabled )
CxE Function (disabled )
Execute Disable Bit ( disabled)
Virtualization Technology (enabled )
Intel HT Technology (enabled )
Active Processor Cores (all )
QPI Control Settings (enabled )
QPI Link Fast Mode (enabled )
QPI Frequency Selection ( auto)
OC Recovery ( enabled)
Turbo Performance (disabled ) 

PnP/PCI     PCI Express
Maximum Payload Size ( )

Power Management Setup
ACPI Suspend Type (S1 )   
HPET Support (enabled )     
HPET Mode ( ) 
So far I'm enjoying the hell out of this CPU.

CPU Clock Ratio (3031  )                                                                                         
CPU Host Frequency (Mhz) (200 ) 

Maybe i have no clue , but 30x200=6.0Ghz? I am confused.

Frequency Control CPU Clock Ratio (25) CPU Host Frequency (Mhz) (200 ) CPU Frequency ( 5017MHz

 
Frequency Control
CPU Clock Ratio (25)                                                                                        
CPU Host Frequency (Mhz) (200 )                                                                      
CPU Frequency ( 5017MHz
 
tried to make in look pretty with colors, Damn Script , LOL

Hey Firex,
 
Wouldn't this be 1.425v (with the new BIOS) and thus be a bad thing?
 
 

robotsociety9

CPU VTT Voltage ( +225 )

4.5 ghz on load 66C not bad!!!

WHAT IS A SAFE MAC TEMP FOR CPU'S

Forget that stupid WEI score musicalman.
It has clearly been shown to be inaccurate and who on Earth knows what its basis is.
For instance, my 920 D0 even at 4.4GHz gets a 7.7
So by that rationale, adding 4 more cores and an even higher clock will only result in +.1 ???
No way in Hades does that make any sense.
So don't base anything off that infernal scoring system.

When you get completely stable for more than 2 mins. on Prime95 musicalman, from your CPU section thread, could you fill out a template?
You're on H20 and we haven't had a water template yet.
Thanks!

Mother Board ( x58 (59) )                                                       
Drivers (  )
Bios ( 49 )                                                                                                     
 CPU (  980x)                   
CPU Cooler ( swiftech apogeegtz )
Memory ( corsair domination GT 7 8 7 20       )
PSU (codsair 1000 )
GPU ( 2x 295 water block )
Drivers (  196.21 )                                                                                                  
Operating System ( win 7 64 ultimate )
temp on cpu 20 C
cores            35C
temp cpu (LOAD)  (33C)
cores (LOAD)        (68C)

Frequency Control
CPU Clock Ratio ( 32 )                                                                                         
CPU Host Frequency (Mhz) (143 )                                                                      
MCH Strap ( auto)
CPU Uncore Frequency (Mhz) ( auto )                                                
CPU Clock Skew ( 0)
Spread Spectrum ( disabled)
PCIE Frequency (Mhz) (100 (SSD's riad 0) ) If using SSDs, Check with your SSD manufacturer before raising above 100.  

Memory Feature        
Memory Speed (2006 )
Memory Control Setting (enabled )
Memory Frequency ( 1867 / 2:14)
Channel Interleave Setting ( 6 way )
Rank Interleave Setting ( 4 way)
Memory Low Gap (auto )
tCL Setting (7 )
tRCD Setting (8 )
tRP Setting ( 7)
tRAS Setting ( 20)
tRFC Setting ( 88)
Command Rate ( 1t)


Voltage Control
EVGA VDroop Control (withoutVDroop )
CPU VCore ( 1.43750)                                                                                                
CPU VTT Voltage (+225 )
CPU PLL VCore ( auto)
**IOH PLL VCore ( auto) 
DIMM Voltage (1.65 )
DIMM DQ Vref (0 )
QPI PLL VCore (1.1 )
IOH VCore ( 1.5)
IOH/ICH I/O Voltage (1.5 )
**BR04 ( NF200) Voltage (1.2 ) (only on E-759)
**VTT PWM Frequency ( 250)
**CPU PWM Frequency (800 )
**CPU Impedance (auto )
**QPI Signal Compensation (auto )
ICH VCore ( auto)
*PWM Frequency ( )


CPU Feature
Intel SpeedStep ( disabled)
Turbo Mode Function ( enabled)
CxE Function ( disabled)
Execute Disable Bit (disabled )
Virtualization Technology ( dasbled)
Intel HT Technology ( enabled)
Active Processor Cores (all )
QPI Control Settings ( enabled)
QPI Link Fast Mode (enabled )
QPI Frequency Selection (6.4 )
OC Recovery ( )
Turbo Performance (disabled ) 

PnP/PCI     PCI Express
Maximum Payload Size ( )
 
Power Management Setup
ACPI Suspend Type (s1(pos) )   
HPET Support (enabled )     
HPET Mode ( 32 bit mode) 

themusicalman

can anyone get a 7.9 windows 7 index score? i got a 7.8!?!??!?! at 4.5 ghz 980x

yeah, I got 7.8 too, musicalman. I don't put too much stock in Windows WEI scores.

chememan

Hey Firex,
 
Wouldn't this be 1.425v (with the new BIOS) and thus be a bad thing?
 
 

robotsociety9

CPU VTT Voltage ( +225 )

Where do you see that in my template??? I'm 1.35v on my CPU VTT.

Not on your template, on Robot's. 

There has been a considerable amount of debate on what the base CPU VTT voltage is for +0 on a non-classified board.  The original BIOS was set to 1.1v but the newer BIOS were allegedly changed to 1.2v, to be the same as the Classified.   

Assuming (you know where that leads) that you need the new BIOS to run a Gulftown, that would make +225 CPU VTT 1.425v. I have read in a few places that CPU VTT over 1.4v were dangerous with a Gulftown.  The newest BIOS either went back to a base of 1.1v or my math skills are totally gone. 

Robot,

I am not doubting what you are reading, I am just trying to figure out what is happening with the base VTT figure.  It was initially 1.1v, then it got raised to 1.2v, only to be returned to 1.1v with the beta BIOS.  

I really don't understand why they chose to have a base figure with a +/- adjustment rather than simply having you set the actual voltage, the way you do with the vast majority of the other voltages.  You add that minor confusion to the fact that they have changed what the base voltage is and it can lead to folks applying more or less voltage than they intended. 

Good luck with your project.

Does anyone know if the Xeon versions are supported on the Classified now?  I went through the bios pages and didn't see anything specifically saying they were supported.
Thanks.