Q56_Monster

Hypn0t1q79

Captian Says MOAR Nitrogen!!!


Hehe

That looks like a classroom....whatcha gonna do with it?

no its not a classroom thats the first floor of the bulding...
 
I work in the mail room at one of the halls at my college (UNH) just so happends that this is where the space science center is and this just is kinda around. probably used for some NASA project there working on atm. never really asked tho i know some of the faculty hehe. i knew it would make people drool when they saw it hehe :)

Hypn0t1q79

no its not a classroom thats the first floor of the bulding...

I work in the mail room at one of the halls at my college (UNH) just so happends that this is where the space science center is and this just is kinda around. probably used for some NASA project there working on atm. never really asked tho i know some of the faculty hehe. i knew it would make people drool when they saw it hehe :)

 
Bring your dewar in and take a tap off it, lol!  Just look like you know what you're doing, hehe.  In the words of Fred Willard (Spinal Tap)..."I'm joking, of course"

You really don't know do you?  Its when you buy something (employee) and don't want your better half finding it.  You ship stuff to your work, and they are not the ones signing for it when UPS delivers it-YOU are ;)
 
Not like I do this of course

wait till you get a serious GF, or wife.  They will watch every penny when it comes to your habits.

My pennies in college went to Old Milwaukee 16oz's

Hypn0t1q79

Q56_Monster

My pennies in college went to Old Milwaukee 16oz's

sadly mine are going into finishing my Wc loop LOL
ive got my priorites straight  

Fixed.
 
And this reminds me of when an old GF, still my best friend actually blew up for like half an hour when she found out I had spent $500 on WC lol.

Benching at 6.5*C and dropping...all air.

xxrabid93

Just set a new q9300 cpuz WR!!! 4164mhz - http://valid.canardpc.com/show_oc.php?id=1527187

http://hwbot.org/community/submission/1088580_xxrabid93_cpu_z_core_2_q9300_2.5ghz_4164.26_mhz?new=true

Nice
Way To Go

xxrabid93

Just set a new q9300 cpuz WR!!! 4164mhz - http://valid.canardpc.com/show_oc.php?id=1527187

http://hwbot.org/community/submission/1088580_xxrabid93_cpu_z_core_2_q9300_2.5ghz_4164.26_mhz?new=true

Good job man!  Man I cannot wait to get back to benching!  Just finished Y axis-  Starting my X axis tonight and hopefully I can figure out how to do that

get on with ya bad self nate diggy dogg block man doo!

Halo_003
Alright new idea, what if you take a Corsair H50/H70, use it to cool the hot side, and the put the coldside facing the Apogee GTZ block(Would be using this in line with main CPU loop).

So the sandwich would look like this...
120mm fan(For H50 rad) - H50 <-- Hotside/Coldside --> Apogee GTZ
While the whole CPU loop would be like:
MCP 355 --> Apogee GTZ(TEC)--> EK Supreme HF(CPU) --> MCP 355
Ideas on temps? If they're low then I'll definitely look into it lol.

Better late than never...
 
In terms of an idea, you're describing the basics of a chiller.  But from the specs, it won't work, at least not with any appreaciable load as intended by the blocks.  Heat from sources has to go somewhere and TEC's are limited in what they can pump unless you have many, and if you do make sure the cooler can remove the TEC heat plus whatever is being pumped through. 
 
That's the part people forget: TEC's aren't coolers, they don't replace a heatsink or a radiator, they only pump heat at the cost of running themselves.  If a unit had a Qmax of 50W and was trying to pump 100W from a source, the hotside is dissipating 150W which a cooler has to deal with otherwise the if the hotside gets too warm, then the coldside gets warm.  If instead the source was 150W, forcing 200W to the hotside, same result, the coldside gets warmer than the hotside.  The system must be balanced and many folks don't do the math expecting miracles and blame the TEC for not getting that result, which frustrates me...
 
I'd try your idea differently, say taking two H50/H70's where one should be modified with two waterblocks where one is sandwiching a TEC with another H50/H70 while the second block is on a source.  This ensures the TEC isn't removing all the heat byitself and is allowed to actually cool the fluid upstream of the source.  If you force the TEC to take it all, it isn't going to cool anything.  In terms of this idea, it's best to keep the loads going into the TEC low, i.e. don't assume this setup can now take a 6-core to 5GHz, it won't happen.   Lower the source load, higher chance for lower temps, that how it is with just about any cooler.  Ultimately if you removed the TEC, you just have a LCS with two rads, how much heat can they support? 
 
Be realistic; TEC's may lower temps if done right, but wattage levels aren't going to change except with more radiators.

Thanks guys! I also upped a few other of my records (haven't posted them though), but my ram was being finnicky, so i stopped. Last night i just set up the UD3P with the q6600 i recently bought. Hopefully i can get some nice overclocks out of that too.

lephron thanks for replying here! That was pretty much my idea, only difference would be I'd add a swiftec 360 as the rad(instead of the modified H70), and use an EK HF Supreme CPU block, with a laing DDC.

Very nice nateman. That should help I imagine.
 
@ Lephron, here's a picture of what I mean..
 

 
 
Color codes...
 
White = tubing
Black = Swiftec 360 rad
Red = 226W TEC plate
Blue = EK HF supreme
Green = motherboard
Brown = H70 block/pump assembly
Pink = Laing 18W DDC pump
Yellow = H70 Rad
Purple outline/white inside = Swiftec GTZ CPU block on TEC
 
Hotside would face the H70 of course, cold side would face the Swiftec GTZ inline before the EK block

Nate, saw the welding write up you did. Nice job! I can't wait until you finish your CNC, then you can really crank out some pots. (and give the first sets free as testers to the GIC crew)