Q56_Monster

I notice you're on HWbot DENTNU.  You should select "evga Enthusiasts" as your team, and post some benchies!

 
ha I had forgot all about that  thanks for reminding me I will do that as soon as I drop off the wife.
 
 
EDIT: So to submit a score to HWbot I have to uninstall my Physx driver and run the test right ? 

yes, i seen dentnu over at mvktech as well...lol
curious to see how this voltage thing works

Ok I need some help. I raise my overclock to 4.8 Ghz and went all the way up to  1.65 vCore. It always Freezes a little over the start of CPU Test 1 of vantage. Any suggestions as I think I need to raise something other than vcore as I saw almost no difference when I raised it litle by little all the way to 1.65v . My blood was pumping alot lol
 
here is the setting I used
 
Frequency Control    
CPU Clock Ratio ( 25x   )                                                
CPU Host Frequency (Mhz) ( 193 )                                   
MCH Strap ( Auto )    
CPU Uncore Frequency (Mhz) ( Auto )                                  
CPU Clock Skew ( 0 ps )    
Spread Spectrum ( Disabled )    
PCIE Frequency (Mhz) ( 105 )   

Memory Feature            
Memory Speed ( Standard )    
Memory Control Setting ( Enabled )    
Memory Frequency ( 1066 / 2:8 )                                
Channel Interleave Setting ( 6 Way )    
Rank Interleave Setting ( 4 Way )    
Memory Low Gap ( Auto )    
tCL Setting ( 7 )    
tRCD Setting ( 7 )    
tRP Setting ( 7 )    
tRAS Setting ( 20 )    
tRFC Setting ( Auto )    
Command Rate ( 1T )    

Voltage Control    
EVGA VDroop Control ( WITH VDroop )    
CPU VCore ( 1.65v )                                                       
CPU VTT Voltage ( +200mv )    
CPU PLL VCore ( auto )    
**IOH PLL VCore ( auto )     
DIMM Voltage ( 1.65 )    
DIMM DQ Vref ( Auto) (+0mV)    
QPI PLL VCore ( auto )    
IOH VCore ( auto )    
IOH/ICH I/O Voltage ( auto )    
ICH VCore (1.1)   
**VTT PWM Frequency ( 250 KHZ )    
**CPU PWM Frequency ( 800 KHZ )    
**CPU Impedance ( Less )    
**QPI Signal Compensation ( Less )    

CPU Feature    
Intel SpeedStep ( Disabled )    
Turbo Mode Function ( Enabled )    
CxE Function ( Disabled )    
Execute Disable Bit ( Disabled )    
Virtualization Technology ( Disabled )    
Intel HT Technology ( Enabled )    
Active Processor Cores ( All )    
QPI Control Settings ( Enabled )    
QPI Link Fast Mode ( Enabled )    
QPI Frequency Selection ( 4.800 GT/s )    
OC Recovery ( Enabled )    

PnP/PCI     PCI Express    
Maximum Payload Size ( 128  )    
    
Power Management Setup    
ACPI Suspend Type ( S3 )       
HPET Support ( Enabled )         
HPET Mode ( 64-bit )    

lol
get your ss up and running...lol

johnksss

lol
get your ss up and running...lol

lol I don't have one.

johnksss

yet......

I like the way you're thinking. I'm actually thinking about trying out a TEC. I have an extra CPU block so it'd be easy to add to the loop. Just need a pump so I could run two loops and an air cooler. Then The cold side of the TEC would face the CPU block while the hot side dumps heat into the HSF... Would be interesting for 24/7 usage.

Well I tried CPU VTT all the way up to 300+ and Vcore all the way to 1.65v. I did start to notice that on CPU test 1 lasted a bit longer than before but it still got stuck. Anyone got any more suggestions ?  I think I need more Vcore but I really do not think it would be safe to keep pushing higher.
 
Thanks

DENTNU

Well I tried CPU VTT all the way up to 300+ and Vcore all the way to 1.65v. I did start to notice that on CPU test 1 lasted a bit longer than before but it still got stuck. Anyone got any more suggestions ?  I think I need more Vcore but I really do not think it would be safe to keep pushing higher.

Thanks

You probably could go higher, I think as long as you're under 1.7 it's alright.(For subzero)
 
VTT... Tricky thing. Maybe try above 300. It's really just guesswork.

xxrabid93

You could probably snag those 2 things in the marketplace fairly cheaply.

On another note, i am getting so ancy to get paid. I need to finish up a few things, and once i get the $, i can say hello to a beautiful SS.

Good idea. lol.

Nice! What rig are you gonna run it on?
 
Jealousy. lol.

lol you suck. I have:
 
i7 930, E758 mb, Dominator GT 2000, GTX 295, 8800GT(with hr03gt). In a rig in Chicago being used by my dad is a X58 micro, HD5770, i7 920 C0, and 12 gigs OCZ DDR3 1600.
 
A CM V10, various fans, a HWlabs Black Ice GTX 480(rad), EK Supreme HF cpu block, Swiftec Apogee GTZ cpu block, EVGA E758 nb/sb block, EK FC-295GTX. lol. Oh and a Laing DDC 18W.

DENTNU

Ok I need some help. I raise my overclock to 4.8 Ghz and went all the way up to  1.65 vCore. It always Freezes a little over the start of CPU Test 1 of vantage. Any suggestions as I think I need to raise something other than vcore as I saw almost no difference when I raised it litle by little all the way to 1.65v . My blood was pumping alot lol

Try going down a notch on the blck.  You went from 189'ish up to 193.  Try 190 or 191 raising vcore a little at a time.  Then 192. 25 or 50mhz can make a big difference believe it or not, so try not to shoot for too much at once.
 
When it freezes, is there a BSOD?  If so, what code?  101 is general more vcore, 124 is generally more vtt.  If it just hangs there and you can push ctrl-alt-del to get out and back to the desktop, then it didn't like the voltage and just stopped running.  If you wait long enough, it might BSOD and give you a code.  I don't like to wait too long if running higher vcore and just exit out of it.

lol well I just found out my CPU @ 1.6vcore doesn't get above 75C in vantage. Good to know the loop can handle it well.

Nice. If you go to options you can select which tests to do btw.

hey q, just tried your bio and it's still locked at 1.138. (from mvktech)
 
haha, but then...that's you bios and not the modded one. *facepalm*
 
 
side note:
 
looking very nice dentnu. keep up the good work.

yeah, thats what i did when i was tying my reply
 
that blackops one seems alright though...
 
side note:
so far...none of them are beating my stock one...so far...grrrrrrrrrrrrrrrrrrrrrrrrrr
which makes me think...the voltage isn't working or i need it colder.