beat it succa!
i pity the fool who don't post pictures when he is suppose to!

Probably the latter. 

Finally Posted... the Air cooled waterblock!
http://forums.evga.com/tm.aspx?m=395778

Fantastic Job Nate

Thank you gents!  I got a few other projects of equal grandeur :P

I have one project that absolutely no one knows about, but It didn't work out as i had hoped, so I never really looked too much into it.  I may just post it in hopes that others can take off where I have failed. 

Hey guys I've made the changes to my bios temp you guys suggested and my temps have gone way down which is great! Thanks again for that, so I'm able to run most every 3D bench without a problem . I'm at a blck of 210 so far and cpu temps are great. However when trying to run with a blck of 212 I mostly get lockups not BSODs. I've tried ram timings at stock setting with no luck a few bumps in different volts, nothing... This is my temp so far...

Mother Board ( EVGA X58 Sli  E758-A )                                                       
Bios ( ? )                                                                                                     
 CPU ( 920 D0)              
CPU Cooler ( Chiller 70-80f )
Memory ( Gskill Trident 16000 7-8-7 22 1t )
PSU ( Corsair HX1000W )
GPU ( 9800 GT but swap everyday )
Drivers ( 190.56 )                                                                                                  
Operating System W7 Pro / Xp Pro

CPU Clock Ratio ( 20X )
CPU Host Frequency (MHz) ( 210 )
MCH Strap (DRAM)
CPU Uncore Frequency (MHz) ( auto )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 108 )
Turb Performance (Disabled)
Extreme Cooling (Disabled)

Memory Feature
Memory Control Setting ( Enabled )
Memory Frequency ( 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Parameters
tCL Setting ( 7 )
tRCD Setting ( 8 )
tRP Setting ( 7 )
tRAS Setting ( 20 )
tRFC Setting ( 88 )
Command Rate ( 1T )

Voltage Control
EVGA VDroop Control ( Without VDroop )
CPU VCore ( 1.53)
CPU VTT Voltage ( +250 )
CPU PLL VCore ( 1.500 )
DIMM Voltage ( 1.65 )     
DIMM DQ Vref ( +0 )
QPI PLL VCore ( 1.25 )
IOH VCore ( 1.375 )
IOH/ICH I/O Voltage ( 1.625 )
ICH VCore ( 1.25 )
PWM Frequency ( 1067 )

CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Enabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Logical Processor Setting
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Settings
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.8 GT/s )

I've had the IOH to 1.3 and the IOH/ICH to 1.5 and still get the same lockups. Am I missing anything that could be holding me back to reach 212 blck or higher?

I wish hoping to try some DICE runs but after all the CPU problems I'm having would it be a waste of money to invest in a pot and mats?

threed, try 8 8 8 24 2T, and up the ram  voltage to 1.7.  if no more crashes, it was your ram that was the problem.   Then try to get your tighter timings back. 

nateman_doo

threed, try 8 8 8 24 2T, and up the ram  voltage to 1.7.  if no more crashes, it was your ram that was the problem.   Then try to get your tighter timings back. 

1.7 Vcore huh well I'll give it a try and let you know.

threedhero

nateman_doo

threed, try 8 8 8 24 2T, and up the ram  voltage to 1.7.  if no more crashes, it was your ram that was the problem.   Then try to get your tighter timings back. 

1.7 Vcore huh well I'll give it a try and let you know.

he means the RAM voltage not vcore

my CPU VTT is usually no less then +300.  and yea, just start with the pci-e around 100

Wasn't sure first time about the ioh and ioh/ich but I think I've got it now. getting lockups at windows loading screen now.

CPU Clock Ratio ( 20X )
CPU Host Frequency (MHz) ( 212 )
MCH Strap (auto)
CPU Uncore Frequency (MHz) ( auto )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) (106)
Turb Performance (Disabled)
Extreme Cooling (Disabled)

Memory Feature
Memory Control Setting ( Enabled )
Memory Frequency ( 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Parameters
tCL Setting (8)
tRCD Setting (8)
tRP Setting (8)
tRAS Setting (8)
tRFC Setting (24)
Command Rate (2T)

Voltage Control
EVGA VDroop Control ( Without VDroop )
CPU VCore ( 1.53)
CPU VTT Voltage ( +200 )May not have to be this high and then again maybe not high enough
CPU PLL VCore ( 1.500 )
DIMM Voltage ( 1.700 )      Try what Natman says then see if you can bring it down
DIMM DQ Vref ( +0 )
QPI PLL VCore ( 1.25 )
IOH VCore ( 1.200 )Unless you are running HIGH end video cards should not have to be this high
IOH/ICH I/O Voltage ( 1.550)This up one for every two on IOH
ICH VCore ( auto ) Tried 1.20 & 1.30     Unless you are having problems booting cause you have like 8 hard drives this can be left on auto
PWM Frequency ( 1067 )

COOOOOOOL

awalleyeguy

CPU VTT Voltage ( +200 )May not have to be this high and then again maybe not high enough  +.300 and see if you can lower v-core

DIMM Voltage ( 1.700 )      Try what Natman says then see if you can bring it down Try like 1.67 might be that 1.65 isn't really putting out 1.65

Most likly the problem is here  Freezing is often mem related I think.
All speculation of course.

Alright thanks awall, I'm also going to try ram at stock settings 9-9-9-26-74. They are rated for 2000mhz so I don't understand why they are being such a pain.

No, this is THE thread for that.....who was holding it & who was taking the pic?