threedhero

I was hoping someone might be able to give a little help I'm stuck at 208 blck. Can't seem to find any combination of volts to be stable.
I boot in to windows at 200 blck, bold print shows the changes I've tried in Eleet. Any tweaks or tips would be great!

Mother Board ( EVGA X58 Sli  E758-A )                                                       
Bios ( ? )                                                                                                     
CPU ( 920 D0)              
CPU Cooler ( Chiller 70-80f )
Memory ( Gskill Trident 16000 7-8-7 22 1t )  Loosen this up
PSU ( Corsair HX1000W )
GPU ( 9800 GT but swap everyday )
Drivers ( 190.56 )                                                                                                  
Operating System W7 Pro / Xp Pro

CPU Clock Ratio ( 20X )
CPU Host Frequency (MHz) ( 200 ) ----- 208
MCH Strap (1600)  Either leave on auto or go for 1866 1866 will lesson performance a bit but help stabilize I think.
CPU Uncore Frequency (MHz) ( 16x )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 106 )
Turb Performance (Enable)  Disable this it is mainly for the 6 core processors.
Extreme Cooling (Mode 1)  leave at default does not seem to do much (maybe I am wrong)

Memory Feature
Memory Control Setting ( Enabled )
Memory Frequency ( 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Parameters
tCL Setting ( 7 )  Just try these at auto for now, can tighten up later
tRCD Setting ( 8 )
tRP Setting ( 7 )
tRAS Setting ( 22 )
tRFC Setting ( 88 )
Command Rate ( 1T )

Voltage Control
EVGA VDroop Control ( Without VDroop )
CPU VCore ( 1.4 ) ------ up to 1.55  These chips do not like to much either
CPU VTT Voltage ( +400 )  No reason to be so high here try +200 to +250 max
CPU PLL VCore ( 1.800 ) ----- Eleet says 1.45  for a 920 DO 1.425 to 1.5 is good
DIMM Voltage ( 1.675 ) -------- up to 1.725   Way too much here put at factory settings    
DIMM DQ Vref ( +0 )
QPI PLL VCore ( 1.425 ) -------- up to 1.55  Way to high try 1.3
IOH VCore ( 1.4 ) ------ up to 1.5  all this is for is video cards mostly if to high messes with everything.
IOH/ICH I/O Voltage ( 1.65 )  up 1 for every 2 in IOH vcore
ICH VCore ( 1.25 ) ------  up to1.4  basically for hardrives no need to be so high 1.1 should be plenty
PWM Frequency ( 1067 )

CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Enabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Logical Processor Setting
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Settings
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.8 GT/s )

Maximum Payload Size (4096)

awalleyeguy

 Yeah but going from 2:8 to 2:10?

threedhero

Alright question is it going to be better for me to boot in at a higher blck? What I'm doing atm is booting in at 200blck and working my way up in eleet. So far wprime bsods at 212blck