KonradGM
New Member
- Total Posts : 8
- Reward points : 0
- Joined: 2016/08/27 14:25:35
- Status: offline
- Ribbons : 0
As in the topic, i managed to screw 3/4 screws into the power supply with it facing down, but i can't screw in the last hole, as seen in this picture the top left hole is hidden behind the case, but the top right one, bottom right one and bottom left one are good for screwin inside 
|
bcavnaugh
The Crunchinator
- Total Posts : 38977
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 14:31:16
(permalink)
Welcome to the Forum KonradGM The PSU is upside down in your Case is why! Or your two bottom Screws are not in the correct Holes of the PSU. But this one circled in Yellow looks ok Loosen the other three screws and put in the forth upper left screw.  It looks like the Bottom screws are also not Level so one must not be correctly installed into the PSU.
post edited by bcavnaugh - 2016/08/27 14:48:22
Attached Image(s)
|
KonradGM
New Member
- Total Posts : 8
- Reward points : 0
- Joined: 2016/08/27 14:25:35
- Status: offline
- Ribbons : 0
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 14:34:25
(permalink)
but doesn't the psu support the bottom intake? even the insturction manual says that if the case supports it i should place the psu with the fan facing down
|
bcavnaugh
The Crunchinator
- Total Posts : 38977
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 14:38:11
(permalink)
I have some up and some down they will fit either way.
|
KonradGM
New Member
- Total Posts : 8
- Reward points : 0
- Joined: 2016/08/27 14:25:35
- Status: offline
- Ribbons : 0
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 14:38:19
(permalink)
the top left one is only slightly available, when i tried to screw the last srew in, it would only do that at an angle, with made me worried about not breaking the psu,
|
bcavnaugh
The Crunchinator
- Total Posts : 38977
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 14:46:50
(permalink)
KonradGM
the top left one is only slightly available, when i tried to screw the last srew in, it would only do that at an angle, with made me worried about not breaking the psu,
Also it looks like the Bottom screws are also not Level so one must not be correctly installed into the PSU.  This also means that the upper screw is not in the Correct Hole as well. Remove all the Screws and start over.
post edited by bcavnaugh - 2016/08/27 14:57:09
Attached Image(s)
|
bcavnaugh
The Crunchinator
- Total Posts : 38977
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 16:16:07
(permalink)
|
KonradGM
New Member
- Total Posts : 8
- Reward points : 0
- Joined: 2016/08/27 14:25:35
- Status: offline
- Ribbons : 0
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 16:18:59
(permalink)
ok 2 screws were wrong i need but they didn't seem to affect position of last one with was only 3/4th exposed , managed to screw last one in by screwing in and out few times
|
KonradGM
New Member
- Total Posts : 8
- Reward points : 0
- Joined: 2016/08/27 14:25:35
- Status: offline
- Ribbons : 0
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 16:22:26
(permalink)
wait I need to repfrase , screws were in right place , I unscrewed it and screwed it back in , can't post the photo of unscrewed sadly
|
KonradGM
New Member
- Total Posts : 8
- Reward points : 0
- Joined: 2016/08/27 14:25:35
- Status: offline
- Ribbons : 0
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 16:26:33
(permalink)
http://i.imgur.com/DiJn4rz.jpg here is pictuŕe while unscrewed , I moved it back to make sure with holes needed to be screwed
|
Cool GTX
EVGA Forum Moderator
- Total Posts : 30978
- Reward points : 0
- Joined: 2010/12/12 14:22:25
- Location: Folding for the Greater Good
- Status: offline
- Ribbons : 122
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 17:45:01
(permalink)
KonradGM
http://i.imgur.com/DiJn4rz.jpg here is pictuŕe while unscrewed , I moved it back to make sure with holes needed to be screwed
Welcome to the forums KonradGM The PSU is not sitting flat in the case. Your own photo shows the left side is much higher than the right side. The solid part of the PSU under the holes shows this clearly. Remove the PSU and look for a cause. Its either the Case or something is in the way ---maybe a wire ? If there is not a part in the way and case is not obstructing / stopping the PSU from sitting flat - could be the PSU was out of spec, when they formed the metal cover --- or the case was poorly made and is out of spec
post edited by Cool GTX - 2016/08/27 18:15:26
Attached Image(s)
|
KonradGM
New Member
- Total Posts : 8
- Reward points : 0
- Joined: 2016/08/27 14:25:35
- Status: offline
- Ribbons : 0
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 17:56:40
(permalink)
we'll how I stated it is screwed in now
|
Cool GTX
EVGA Forum Moderator
- Total Posts : 30978
- Reward points : 0
- Joined: 2010/12/12 14:22:25
- Location: Folding for the Greater Good
- Status: offline
- Ribbons : 122
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 18:04:12
(permalink)
Glad you got it sorted  I like my Phanteks Primo Case -- hope you enjoy your Enthoo Pro  Thought that it was well made, had no sharp edges 
post edited by Cool GTX - 2016/08/27 18:09:47
Attached Image(s)
|
KonradGM
New Member
- Total Posts : 8
- Reward points : 0
- Joined: 2016/08/27 14:25:35
- Status: offline
- Ribbons : 0
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 18:06:18
(permalink)
I like I too :P but it makes my curious about what you sayed there was no cable under the psu , so I'm not sure how it could be uneven , but how they say if it works it works?
|
Cool GTX
EVGA Forum Moderator
- Total Posts : 30978
- Reward points : 0
- Joined: 2010/12/12 14:22:25
- Location: Folding for the Greater Good
- Status: offline
- Ribbons : 122
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 18:16:43
(permalink)
KonradGM
I like I too :P but it makes my curious about what you sayed there was no cable under the psu , so I'm not sure how it could be uneven , but how they say if it works it works?
If it works don't fix it  Is how I have heard it
|
bcavnaugh
The Crunchinator
- Total Posts : 38977
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/27 20:50:35
(permalink)
Cool GTX
KonradGM
http://i.imgur.com/DiJn4rz.jpg here is pictuŕe while unscrewed , I moved it back to make sure with holes needed to be screwed
Welcome to the forums KonradGM
The PSU is not sitting flat in the case. Your own photo shows the left side is much higher than the right side.
The solid part of the PSU under the holes shows this clearly.
Remove the PSU and look for a cause.
Its either the Case or something is in the way ---maybe a wire ?
If there is not a part in the way and case is not obstructing / stopping the PSU from sitting flat - could be the PSU was out of spec, when they formed the metal cover --- or the case was poorly made and is out of spec
Is this not the same thing? From http://forums.evga.com/FindPost/2539938
|
stevenli1966
New Member
- Total Posts : 38
- Reward points : 0
- Joined: 2014/07/17 20:10:41
- Status: offline
- Ribbons : 0
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/28 09:41:01
(permalink)
I have the same case, with a G2 550. I had an old CX650M that fit perfectly but when I tried to seat my G2 one screwhole would always be obstructed. Upon further inspection, the case's psu compartment is too tight OR the housing for the G2 is a bit big. I ended up just screwing 3/4.
|
Cool GTX
EVGA Forum Moderator
- Total Posts : 30978
- Reward points : 0
- Joined: 2010/12/12 14:22:25
- Location: Folding for the Greater Good
- Status: offline
- Ribbons : 122
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/08/28 09:56:55
(permalink)
stevenli1966
I have the same case, with a G2 550. I had an old CX650M that fit perfectly but when I tried to seat my G2 one screwhole would always be obstructed. Upon further inspection, the case's psu compartment is too tight OR the housing for the G2 is a bit big. I ended up just screwing 3/4.
That will work
|
Cool GTX
EVGA Forum Moderator
- Total Posts : 30978
- Reward points : 0
- Joined: 2010/12/12 14:22:25
- Location: Folding for the Greater Good
- Status: offline
- Ribbons : 122
|
XRogerX
Superclocked Member
- Total Posts : 220
- Reward points : 0
- Joined: 2011/08/01 15:58:03
- Status: offline
- Ribbons : 2
Re: Evga 750W g2 and Phanteks Enthoo Pro - Not all holes allign
2016/09/03 15:04:01
(permalink)
I know this is 6days old but I got this same case and the last time I knew all PSU screw holes are the same I had to take a picture of mine and post it , everything is even 
MB: EVGA Z170 Classified K CPU: I7 6700K VGA:EVGA GTX 1070SC Memory: G.SKILL TridentZ 16GB PSU: CORSAIR RM1000 HD: Kingston SSDNow V300 Cooling: Swiftech 240 x2 prestige
|