Codybby
New Member
- Total Posts : 99
- Reward points : 0
- Joined: 2014/02/06 11:57:47
- Status: offline
- Ribbons : 1
Hey guys, I'm planning my next build with x99 right around the corner and need some input. I have a corsair 900D case with 2 480's and a 240mm rad and I'm wanting to know at what point 2 D5's would start to be needed, I would like the ability to cool 4GPU's,CPU,Mobo,etc with several 90 degree fittings and 3/8 x 1/2 tubing. Now with that said starting out I will only be cooling 2 GPU's and the CPU and I would think a single D5 could handle that. But as time goes on I'd like the option of expanding the loop without replacing the pump. Should I go ahead and buy a dual pump combo now, or will a single D5 handle everything I'll be throwing at it?
|
the_Scarlet_one
formerly Scarlet-tech
- Total Posts : 24581
- Reward points : 0
- Joined: 2013/11/13 02:48:57
- Location: East Coast
- Status: offline
- Ribbons : 79
Re: Is a single D5 enough?
2014/08/27 08:34:01
(permalink)
Cooling that much is going to take a large surface area to pull heat away. I currently run a 4770k and 3 GPUs, and it gets warm, and I have a lot of radiator surface area. I would suggest 2 pumps, so that you can run the cpu and motherboard parts separate from the GPUs.
Running 2 loops is going to allow the heat to be dissipated much more efficiently. And will also not allow the hest of the cpu to dump extra hest into the loop and cause a possible overheating issue in total.
|
Codybby
New Member
- Total Posts : 99
- Reward points : 0
- Joined: 2014/02/06 11:57:47
- Status: offline
- Ribbons : 1
Re: Is a single D5 enough?
2014/08/27 08:44:35
(permalink)
Scarlet-Tech Cooling that much is going to take a large surface area to pull heat away. I currently run a 4770k and 3 GPUs, and it gets warm, and I have a lot of radiator surface area. I would suggest 2 pumps, so that you can run the cpu and motherboard parts separate from the GPUs.
Running 2 loops is going to allow the heat to be dissipated much more efficiently. And will also not allow the hest of the cpu to dump extra hest into the loop and cause a possible overheating issue in total.
According to everything I've read dual loops make a negligible difference, although that could only be the case for small loops and the more you try to cool the more dual loops start to have an advantage possibly?
|
the_Scarlet_one
formerly Scarlet-tech
- Total Posts : 24581
- Reward points : 0
- Joined: 2013/11/13 02:48:57
- Location: East Coast
- Status: offline
- Ribbons : 79
Re: Is a single D5 enough?
2014/08/27 08:48:42
(permalink)
I know running my cpu, it is currently running 45-50c. Add one gpu, it goes up a few c, to 53c or so... Then 2 goes up to 60c... 3 up to 70c.. That isn't negligible if you ask me.
|
Codybby
New Member
- Total Posts : 99
- Reward points : 0
- Joined: 2014/02/06 11:57:47
- Status: offline
- Ribbons : 1
Re: Is a single D5 enough?
2014/08/27 08:51:34
(permalink)
Scarlet-Tech I know running my cpu, it is currently running 45-50c. Add one gpu, it goes up a few c, to 53c or so... Then 2 goes up to 60c... 3 up to 70c.. That isn't negligible if you ask me.
How much rad are you running, just out of curiosity?
|
the_Scarlet_one
formerly Scarlet-tech
- Total Posts : 24581
- Reward points : 0
- Joined: 2013/11/13 02:48:57
- Location: East Coast
- Status: offline
- Ribbons : 79
Re: Is a single D5 enough?
2014/08/27 08:55:27
(permalink)
1 - 120mm: exhaust 1 - 280mm: exhaust 1 - 280mm: intake 1 - 240mm: intake
I also run dual pumps, because with a single pump, there was always an air bubble in the top rad that caused microbubbles. After installing the second pump, the microbubbles were gone in a couple of hours.
|
Codybby
New Member
- Total Posts : 99
- Reward points : 0
- Joined: 2014/02/06 11:57:47
- Status: offline
- Ribbons : 1
Re: Is a single D5 enough?
2014/08/27 08:59:51
(permalink)
Scarlet-Tech 1 - 120mm: exhaust 1 - 280mm: exhaust 1 - 280mm: intake 1 - 240mm: intake
I also run dual pumps, because with a single pump, there was always an air bubble in the top rad that caused microbubbles. After installing the second pump, the microbubbles were gone in a couple of hours.
Nice, I think I'm gonna go ahead opt for a second pump but hold off on the dual loops just because I don't have the hardware that calls for it right now. It's just a CPU and 2 GPU's at the moment.
|
the_Scarlet_one
formerly Scarlet-tech
- Total Posts : 24581
- Reward points : 0
- Joined: 2013/11/13 02:48:57
- Location: East Coast
- Status: offline
- Ribbons : 79
Re: Is a single D5 enough?
2014/08/27 09:06:50
(permalink)
Just the cpu and 2 GPUs will be perfectly fine. Just think, each new components needs approximately 120mm of cooling space. I am switch the exhaust 280 out for a 360mm and going to look into going with dual loops as well.
|
TECH_DaveB
EVGA Alumni
- Total Posts : 4893
- Reward points : 0
- Joined: 2008/09/26 17:03:47
- Status: offline
- Ribbons : 46
Re: Is a single D5 enough?
2014/08/27 09:25:37
(permalink)
Codybby
Scarlet-Tech Cooling that much is going to take a large surface area to pull heat away. I currently run a 4770k and 3 GPUs, and it gets warm, and I have a lot of radiator surface area. I would suggest 2 pumps, so that you can run the cpu and motherboard parts separate from the GPUs.
Running 2 loops is going to allow the heat to be dissipated much more efficiently. And will also not allow the hest of the cpu to dump extra hest into the loop and cause a possible overheating issue in total.
According to everything I've read dual loops make a negligible difference, although that could only be the case for small loops and the more you try to cool the more dual loops start to have an advantage possibly?
It is negligible if you are doing CPU on one, and 2 way SLI on the other. If you have lots of case space it can make things easier for maintenance, but for bigger loops dual and 2 pumps is a really good idea. Also, 480s produce a LOT of heat as well as most of the blocks have a bit of restriction, I have seen a similar loop to that done, and after a while on a single pump, temps were much warmer and the impeller on the pump was toasted, a loop that size REALLY needs 2 pumps, and using 2 loops would make things easier too, and cooler.
|
owcraftsman
CLASSIFIED Member
- Total Posts : 4754
- Reward points : 0
- Joined: 2005/04/16 16:41:02
- Location: Cape Coral, Florida
- Status: offline
- Ribbons : 60
Re: Is a single D5 enough?
2014/08/27 17:25:09
(permalink)
IMO Single loop with dual D5 is appropriate for your proposed system. If for no other reason than redundancy it's a great idea. Also with 2 pumps both will work less hard. Separate the pumps to boost head pressure and increase flow rate best. Say your pump 1 is at the beginning of the loop place the 2nd in the middle of the loop preferably 1 before and 2 after the waterblocks which are the most restrictive to help pick back up the pressure and flow. Dual Pump tops are sweet for saving space but I'd argue it's more efficient the way I propose. Eliminate as many 90s as you can. For an alternative many times a swivel 45 are usable and slightly less restrictive especially when using flexible tubing. GL
5800X3D | ROG Crosshair VIII Hero w/EK-Q-M-Full | Trident Z Neo 4x8 3600 C16 | EVGA RTX 3090 FTW3 Ultra w/EK-QV2-ABP +150 CC/+1000 MC | LG 34GP83A-B UW-QHD/2-Asus PB278Q | EVGA Supernova 1000 G2 | Corsair 1TB MP600 (OS) & 970 EVO 1TB M.2 (Games) | Custom Phanteks Enthoo Luxe | NexXxoS UT60 1080mm Nova | 2x D5 w/BP-2D5TOPPEX-BK | Win-10-pro 21H2 RIG PICS
EVGA Affiliate Code GMER9XL4N
|
movieman
FTW Member
- Total Posts : 1114
- Reward points : 0
- Joined: 2005/11/14 18:06:46
- Status: offline
- Ribbons : 5
Re: Is a single D5 enough?
2014/09/06 11:55:21
(permalink)
I hope to put separate GPU loop in by the end of the year. I am not sure if my loop can handle another device. Scarlet-tech is right about the bubbles. Before I added my second rad and VRM block, my bubbles would be gone within a couple of hours. With 2 Rads and 3 blocks, it took a week for the bubbles to get free and I had to do a lot of moving my case around. Moving a 900D full of water is not easy, :/. I think this means that I might be close to my max number of devices to push water through on one pump.
post edited by movieman - 2014/09/06 11:57:39
NZXT B550 AMD 5950X EVGA 3080Ti Hydrocopper WD Black 2TB NVME Corsair 64GB (4 x 16GB) Alienware AW3418DW 34" UW Corsair HX 850 Corsair 5000X(white) Windows 10 HEATWARE
|
RainStryke
The Advocate
- Total Posts : 15872
- Reward points : 0
- Joined: 2007/07/19 19:26:55
- Location: Kansas
- Status: offline
- Ribbons : 60
Re: Is a single D5 enough?
2014/09/07 14:08:59
(permalink)
I would try one, then add a second if you are not happy with the performance.
Main PC | Secondary PC Intel i9 10900K | Intel i7 9700KMSI MEG Z490 ACE | Gigabyte Aorus Z390 MasterASUS TUF RTX 3090 | NVIDIA RTX 2070 Super32GB G.Skill Trident Z Royal 4000MHz CL18 | 32GB G.Skill Trident Z RGB 4266MHz CL17SuperFlower Platinum SE 1200w | Seasonic X-1250Samsung EVO 970 1TB and Crucial P5 1TB | Intel 760p 1TB and Crucial MX100 512GBCougar Vortex CF-V12HPB x9 | Cougar Vortex CF-V12SPB-RGB x5 3DMark Results:Time Spy|Port Royal
|
TECH_DaveB
EVGA Alumni
- Total Posts : 4893
- Reward points : 0
- Joined: 2008/09/26 17:03:47
- Status: offline
- Ribbons : 46
Re: Is a single D5 enough?
2014/09/15 17:22:31
(permalink)
Ownscraftsman is definitely correct, it will help, necessary, I doubt it but possible. In your place I would do what RainStryke recommended. You can always add in another one. I have thought about adding in a secondary on both of my loops, but really, the challenge is mounting it, as I would do it inline.
|