New parts list for water cooling loop and accessories.
 
Swiftech Maelstrom 51/4" dual bay reservoir with dual MCP35X pumps
 
COUGAR CF-V12HP Vortex Hydro-Dynamic-Bearing (Fluid) 300,000 Hours 12CM Silent Cooling Fan with Pulse Width Modulation =3
 
COUGAR CF-V14H Vortex Hydro-Dynamic-Bearing (Fluid)300,000 Hours 14CM Silent Cooling Fan =1
 
3mm Blue LED =3
 
Bitspower Ultimate G 1/4 Thread 1/2" ID x 3/4" OD Compression Fitting -Matte Black =10
 
Danger Den DreamFlex Value Pack -Tubing / Clamps / Tube Cutter ( 1/2"ID x 3/4"OD )UV Red =1
 
Bitspower Deep Bold Red O-Ring - (10 Pack) (BP-WTP-010-DRD)=2
 
XSPC EX140 Single 140mm Low Profile Split Fin Radiator =1
 
Bitspower G1/4" Matte Black Dual Rotary 45-Degree Compression Fitting CC5 For ID 1/2" OD 3/4" Tube (BP-MB45R2CPF-CC5)=3
 
Swiftech Maelstrom 5 1/4" Dual Bay Standalone Reservoir w/ Dual MCP35X Pumps(Maelstrom-35X2
 
XSPC RX360 Triple 120mm Radiator Rev 2. =1
 
XSPC RayStorm High Performance Acetal CPU Liquid Cooling Block - Special Edition Copper =1
 
IandH Silver KillCoils - Antimicrobial .999 Fine Silver Tubing / Reservoir Strip =1
 
Bitspower G1/4" Mini Valve - Matte Black (BP-MVV-MBK)=1
 
Swiftech Lok-Seal™ 4-Way Manifold G1/4 Thread - Black (4W-G1-4-TA-BK)=1
 
Monsoon Premium G 1/4 Stop Fitting - Matte Black (MON-SPL-MB)=2
 
Koolance Nozzle Coupling Adapter - Male-Male - Black (ADT-XMM-BK)=1
 
EK 4-Pin PWM 4-Way Splitter Cable - Sleeved Black / Black =1
 
ModRight Black-Out Series 4-Pin 18AWG Extension Cable - 24" =1
 
FrozenCPU LED Power Cable - Standard 3-pin Power Connector =2
 
Dual Ended Universal Molex Removal Tool =1
 
Mod/Smart 3/8" Purse Lock Twist Tie - UV Red (10 pack)=1
 
Mod/Smart 1/4" Purse Lock Twist Tie - UV Red (10 pack)=1
 
Akasa PROSLIM Super Slim SATA 3.0 Data Cable w/ Sec. Latch -30cm-Black (AK-CBSA05-30BK) =1
 
Black SATA 3.0 10" Cable w/ Latch - Straight to Straight (SCIII-10-BK) =5
 
Mod/Smart Double 1/2" Purse Lock Twist Tie - UV Red (5 pack)
 

Just removed every thing from HAFX case.
Need remove the Duel bay hot swap system


Now to remove top 200mm fans.

I need to remove the 2 existing rad mounts from the top of case.
 
I decided the RX360 rad needed to be moved about 1 1/2"  toward the front of case.
 
Implements of destruction below


Let the fun begin

Tired, ordering more goodies.

more work tomorrow!

This is going to look nice. Cant wait to see the finished product.

 
You will definately have fun with that.    :)

XrayMan
Thanks, & yes it will be fun now that I have the planning and lay out in my head.

I like what I see, looks promising! Keep up the good work!

I had to install mother board prior to rad installation to be able to connect the two 8 pin EPS cables. 
Well I have the rads roughed in case to check fitting plan. Top mounted RX360 cougar fans on top of rad pulling air out (exhaust) good to go. 

Ex140 rad, I wanted fittings at the top, but after close analysis I decided water loop layout will look better with them at the bottom.
Reinstall cougar 140mm, fan between back of case and rad also pulling air out (exhaust).

MUCH BETTER
 Moving on later.

aka_STEVE_b
Thanks!
I ordered those from corsair end of September they had a sale $53.00 delivered. Too good to pass up.

Thanks! nookie420

Looking super, can't wait for the final finish photos. 

Wish I could give more than a +1. That is one fine rig there.

rlb682
I can't thank you enough for the kind words!
I just looked at yours, very nice and a +1 for you as well

Back to work on the water loop.
I installed  the base of the compression fittings into CPU block, cleaned the CPU and Block and applied the Phobya HeGrease Extreme Thermal Paste, then installed CPU water block.
FYI. The 1/2" x3/4" compression fittings are too close together on this CPU water block, I literately put some outwards pressure on the fittings while I was trying to tighten them to keep from scraping off the paint on the fittings. 
Finished most of the water loop & literally threw in enough cables to use the paper clip jumper to run the pumps for several hours to leak check loop. All went well
I have working man hands & my fingers still got sore from tightening the compression fittings.

A bit of info on the pumps and fan controls. I decided to connect the pumps to CPU fan header via PWM in bios on Z68ftw, adjusting pump Speeds according to CPU temps in 10 degree increments. Attached the 4 cougar fans mounted to the radiators to the other bios controlled fan header on the Z68FTW. I will need to play around with those settings to get the best results.
Now for more shopping, Might need some more lighting & misc. cables.
 
Mod/Smart SATA 15 Pin Power Extension Cable - Black - 12" (PC-S15P-12X-BK)     =1
wir-47     Mod/Smart Kobra SS Pre-Sleeved Molex Male to Female Extension Wire - 24" - Black (WIRE-M24MF-BK) =4
FrozenCPU ConnectRight Standard 4-pin Female Connector - Black =4
FrozenCPU ConnectRight Standard 4-pin Male Connector - Black =4
Akasa PROSLIM Super Slim SATA 3.0 Data Cable w/ Securing Latch - 30cm - Black (AK-CBSA05-30BK) =1
4-Pin Y Cable Splitter - All Black - 3" =1
Mod/Smart Kobra SS Pre-Sleeved Molex Male to Female Extension Wire - 16" - Black (WIRE-M16MF-BK) =4
Enermax T.B. Apollish 80mm x 25mm LED Fan w/ Focus Blades - Blue (UCTA8N-BL) =1
12" Cold Cathode Kit (Dual Ready) - Ultra Bright UV =1
 
FrozenCPU & Discover should both send me Christmas gifts