lolmont
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2009/12/03 18:54:05
- Location: Brooklyn, NY
- Status: offline
- Ribbons : 0
Hello I recently bought a SSD and I was about to install windows so I went to switch ACHPI mode on and when I saved that in the bios my computer now won't boot, the post code shows 25 and it just keeps turning off and on. Any idea what's going on?
|
loveha
Omnipotent Enthusiast
- Total Posts : 10497
- Reward points : 0
- Joined: 2009/09/26 01:51:22
- Location: Beulah Michigan
- Status: offline
- Ribbons : 65
Re:EVGA x58 slightly error code 25
2011/12/24 12:30:11
(permalink)
Do you have any other HDD's in the computer? If so unhook them and try again. Also what BIOS are you running? What Motherboard? Not sure why you would be getting a post code from adding a SSD. You sure that isn't your CPU temp?
Case - Phanteks Enthoo Evolv XMobo - EVGA X570 FTWCPU - AMD Ryzen 9 5900XRAM - 32GB Trident Z Royal 3600MHz 14-14-14-34GPU - EVGA RTX 3080 Ti FTW3 Ultra GamingPSU - Seasonic Prime TX-1000Heatkiller IV CPU Waterblock / Heatkiller V GPU WaterblockHeatkiller V EBC Active Backplate / Two Heatkiller Rad 360 L Six Noctua NF-A12x25 / Heatkiller D5 Pump
|
lolmont
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2009/12/03 18:54:05
- Location: Brooklyn, NY
- Status: offline
- Ribbons : 0
Re:EVGA x58 slightly error code 25
2011/12/24 12:35:40
(permalink)
100% sure not cpu temp, I have all old HDD unhooked don't remember the bios name but it came out 4/20/2011
|
loveha
Omnipotent Enthusiast
- Total Posts : 10497
- Reward points : 0
- Joined: 2009/09/26 01:51:22
- Location: Beulah Michigan
- Status: offline
- Ribbons : 65
Re:EVGA x58 slightly error code 25
2011/12/24 12:46:07
(permalink)
What if you go back to IDE? Have you tried hooking up your old drives to see if you did something to your board during all this? What motherboard? Is it hooked into the Intel SATA II ports?
Case - Phanteks Enthoo Evolv XMobo - EVGA X570 FTWCPU - AMD Ryzen 9 5900XRAM - 32GB Trident Z Royal 3600MHz 14-14-14-34GPU - EVGA RTX 3080 Ti FTW3 Ultra GamingPSU - Seasonic Prime TX-1000Heatkiller IV CPU Waterblock / Heatkiller V GPU WaterblockHeatkiller V EBC Active Backplate / Two Heatkiller Rad 360 L Six Noctua NF-A12x25 / Heatkiller D5 Pump
|
lolmont
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2009/12/03 18:54:05
- Location: Brooklyn, NY
- Status: offline
- Ribbons : 0
Re:EVGA x58 slightly error code 25
2011/12/24 13:11:22
(permalink)
E758 and yes it's in the intel sata II ports, problem is it's not posting and when I clear cmos still keeps going back to 25
|
KMoore4318
Pistoj Doulos Unum Pluribus
- Total Posts : 17850
- Reward points : 0
- Joined: 2008/12/04 04:20:57
- Location: Atlanta, Ga
- Status: offline
- Ribbons : 238
Re:EVGA x58 slightly error code 25
2011/12/24 13:14:32
(permalink)
Set your CD/DVD to the first boot device then try to load windows while it's in AHCI mode.
Just clink Link to Register > My Affiliate Code:VTJPDC4OMB 1)965 V-8 E761(77) 2)980X AX1200 E760(77) 980 ti 3) E770 (77)2(590) SLI AX1200 4) X299 FTW K, 9980XE 2 2080 supers on AX1200
|
lolmont
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2009/12/03 18:54:05
- Location: Brooklyn, NY
- Status: offline
- Ribbons : 0
Re:EVGA x58 slightly error code 25
2011/12/24 13:17:31
(permalink)
I would if I could even get it to post, odd thing is I unhooked the SSD had no drives but dvd in and it loaded the windows disk. I replugged the SSD and bam error 25 again.
|
KMoore4318
Pistoj Doulos Unum Pluribus
- Total Posts : 17850
- Reward points : 0
- Joined: 2008/12/04 04:20:57
- Location: Atlanta, Ga
- Status: offline
- Ribbons : 238
Re:EVGA x58 slightly error code 25
2011/12/24 13:23:49
(permalink)
Just clink Link to Register > My Affiliate Code:VTJPDC4OMB 1)965 V-8 E761(77) 2)980X AX1200 E760(77) 980 ti 3) E770 (77)2(590) SLI AX1200 4) X299 FTW K, 9980XE 2 2080 supers on AX1200
|
loveha
Omnipotent Enthusiast
- Total Posts : 10497
- Reward points : 0
- Joined: 2009/09/26 01:51:22
- Location: Beulah Michigan
- Status: offline
- Ribbons : 65
Re:EVGA x58 slightly error code 25
2011/12/24 13:29:16
(permalink)
Darklink25 I would if I could even get it to post, odd thing is I unhooked the SSD had no drives but dvd in and it loaded the windows disk. I replugged the SSD and bam error 25 again. Sounds like an SSD issue, which SSD is it?
Case - Phanteks Enthoo Evolv XMobo - EVGA X570 FTWCPU - AMD Ryzen 9 5900XRAM - 32GB Trident Z Royal 3600MHz 14-14-14-34GPU - EVGA RTX 3080 Ti FTW3 Ultra GamingPSU - Seasonic Prime TX-1000Heatkiller IV CPU Waterblock / Heatkiller V GPU WaterblockHeatkiller V EBC Active Backplate / Two Heatkiller Rad 360 L Six Noctua NF-A12x25 / Heatkiller D5 Pump
|
lolmont
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2009/12/03 18:54:05
- Location: Brooklyn, NY
- Status: offline
- Ribbons : 0
Re:EVGA x58 slightly error code 25
2011/12/24 13:31:52
(permalink)
Well I don't think it's the drive I plugged in my old drive same problem, I looked up the error code says something to do with PS/2 devices which I have none a bad gpu but I've seen my gpu show graphics when it went to the windows install. This is very confusing.
|
lolmont
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2009/12/03 18:54:05
- Location: Brooklyn, NY
- Status: offline
- Ribbons : 0
Re:EVGA x58 slightly error code 25
2011/12/24 13:33:54
(permalink)
|
lolmont
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2009/12/03 18:54:05
- Location: Brooklyn, NY
- Status: offline
- Ribbons : 0
Re:EVGA x58 slightly error code 25
2011/12/24 14:18:31
(permalink)
I somehow fixed it installed windows with achi, got a 7.8 on disk drive. Now I just wonder how good this SSD is on Sata3
|