For you EVBot users, we now have a way to flash EVBot using the graphics card! An EVGA motherboard is no longer required for flashing.
 
EVBot GPU Flash 1.0.0.2:

• Initial release

Graphics Cards Supported:

• EVGA GeForce GTX 680 Classified
• EVGA GeForce GTX 580 Classified
• EVGA GeForce GTX 285 Classified

 

---

Windows Installation

• Download the .zip file below:

         EVBot GPU Flasher 1.0.0.2

• Connect the EVBot cable to the MB port located on the EVBot device.
• Connect the other end of the EVBot cable to your graphics card.
• Extract contents of above .zip file and run EVBotFlashTool.exe
• Select the bundled .hex file for flashing.

• Hold down the EVBot POWER button for 7 seconds until you see the EVBot screen display FLASH MODE.

• Click OK in EVBot Flash Tool to being the flashing process.
• After flash is complete, unplug EVBot, then plug it back in to any EVBot port.

Warning:
**Do not restart or interrupt your PC while the flash is ongoing

 

fantastic

why after click the ok, cannot find EVBot device?
 

thanks,i get it . i get GTX680 Classfied ,is possibly to work  in 1.35V(NVVDD) with EVBot?

I had the same error, ended up just closing everything out and trying again and it worked.
 
On a different not though, I flashed my other EVBot to the 580 firmware without issue, however it is not allowing me to raise the VGPU on the card, says I fail
 

nice posts i like it......

EVGA might of just F-UPed! my Evbot!
 
I followed these directions to the T and i got the error that everyone else is getting!
SO my Evbot displayed the words "Flash mode" and the screen light went on and off constantly.  I tried closing the EVbot Flash tool and reopening it and trying it again to no avail!
 
But now i think this might have F-upped my EVbot cause now every time i plug the cable back into my GPU the Evbot lights up and displays nothing but a black box on the screen!!!  I cant even get it to go into flash mode anymore!!
 
EVGA!  Please Help me!
 
Okay!
After playing around with the evbot, i was able to get it back into flash mode by doing the following:
"unplugged the cable from the MB port with the other end still plugged into my GPU.  Then i held down the power button while plugging cable back into the MB port.  I continued to hold down the power button for about 7 seconds and it showed flashmode on the Evbot LCD.   WhEW!!!!!
 
I tried the Flashtool again and it worked!   Who new?!
 
I uplugged the power to the EVbot and plugged into one of the VGA ports on the Evbot instead.
 
The Evbot now reads " EVGA EVBOT For EVGA VGA and shows V019 on the bottom right of the Evbot LCD"
 
Is this the right Version?
 
Can someone please confirm that the Flashtool updates the Evbot to V019?
 
Please?

Okay,
 
This post is all good and fine, but do i need to run the EVGA Evbot Flash Tool for each GPU in my system? 
 
The reason why i ask this is because i am confused with the menu options on my Evbot.
 
Like i mentioned above, i have VGA0 VGA1 VGA2 VGA3
Now like i said, i have only 3 gpu's
 
If i select VGA0,  I get the following:
Vcore
VPLL
VDD
VDDQ
 
If i select vga1,2 or 3, i get the following:
 
NVVDD
FBVDD
PEXVDD1
PEXVDD2
OCP
 
I dont see what i saw on VGA0.
 
If i make a change to VGA0, does it affect all my GPU's simultaneously?
 
Before you ask, yes i have read the instructions throroughly and even looked up online and nothing explains this.
 
 

like!!

The Nach is the EVBot a worthwhile companion?

It depends a lot on what do you think to do with it, I mean, if you just want to overclock your videocard "a little bit", I think it is not worth, but if you are the kind of hardware torturing guy, then, I think it is a nice and friendly help. I've been able to reach 1450 Mhz on each of my 680's Classified with the EVBot's help.

I received my EVBOT today and I am not finding where on the GTX 680 Classified Video to plug in the cable. Did I waste my hard earned money on the EVBOT? All 3 of my GTX 680 Classified Cards are new.
Thanks for any help,
Bill
I can connect it to my x79 FTW with no problems. Even updated the Firmware.

bcavnaughI received my EVBOT today and I am not finding where on the GTX 680 Classified Video to plug in the cable.

Check these links:
 
http://forums.evga.com/tm.aspx?m=1755509
 
http://kingpincooling.com/forum/showpost.php?p=23414&postcount=3
 

Can i also flash with 780 classi?

 
 
Also regarding the EVbot, if I alter the voltages on my cards, is the change permanent or do I loose the over-clock once the machine is powered off.
 
Hopefully I am posting in the right place and someone will be able to assist.
 
 
EDITED: You would need to post in the WTB section for that, which you also need 50 posts to do, and auth from Evga. The WTB portion of this post has been edited out / deleted.

hello jpmboy :>