D.M.W.T

norum

Fine! Thanks, i Will try tonight with new cooler and see what's happening if the problem persists I don't post nothing. I will POST tomorrow in work so. I know that you are experienced users, but I'm said I have problems, my pc is shutdown or presents the FF and Red Light Problem because the FF or no present the redlight, but shows only FF and do nothing.

So I hope that I can test your settings in post#6

Not to jump in and misdirect anyone, but if I am reading correctly the red light at the top of the board is on or coming on? beofre or while its shutting itself off? This problem right after a new cooler was installed?
 

I gotta say unless I a missing something I really think you need to follow the above step in post # 2 again with the stock cooler jsut to see what happens. I think your messing something up (not on purpose of course), but it seems too coincidental that it was stable for 3 years then right after a cooler install it shuts down immediately and wont post.

 
Yes DMWT, it's simple, my pc is running fine. I install and reinstall CPU FRIO sometimes, and it's make me arrive at this point, well I'm in the desktop, but it's shutdown, I using my old EVERCOOL Buffalo(need change the screws).  My four push-pins are not properly seated. I have one with problem think so. Because of this I test a CPU COoler with push-pins ok.
 
 
 

Well! By pass:
 
1) I unmount all my system and put in the table and clean all the motherboard and other components.
 
2) I mount in the table the board and other components and it's running fine.
 
3) In Test, because this photo was maked yesterday and PC is shutdown with a non clean.
 
4)TESTING in CM690 since 7:00 am. 12:00 I will see if the system is on and working fine, but cooler box is so "f...$#%"
 
So When I fix my FRIO is good to reinstall in my system?
 
Thanks.

No!
I'm Using stock settings and some settings of post 6. Because I try to Use this settings and my pc not running. Hang up and doesn't make the job and my system will overheat more. My pc is shutdown again. ]
 
I think it's my case, in a board it's load normal, when I put in the case this not function normal.

All is fine, I have a GOod Airflow. Now we need know what's shutdown the pc. IF the PC is shutdown, when I try to turn it on, they Stay FF and RED LIGHT and other leds. Stock settings hum! I can Try if I can do it through The bios.

Yes! It's Run, I restart sometimes to put other things. HD, Coolers, Drive IDE, memory, and no failure, the red led function normal, just lit 2 times and the pc Loading normal, but when shutdown abnormal in the case the red light come lit and I can't get through the cycles. Just FF + lights or pc shut itself

Please try the following.  Please remove the board from the case, install all of your hardware except only install two of the RAM sticks in the black slots, and then try all of the below settings.  Make sure all connections are fully seated.
BIOS Version: P08
**System **
CPU Freq, MHz: 3000 GHZ
FSB Reference Clock, MHz: 333 (1333)
CPU Multiplier: [9X]
PCle x16-1 & 16-2, MHz:  [AUTO]
PCle x16-3, MHz:  [AUTO]
SPPc->MCP Ref Clock, MHz:  [AUTO]
nForce SPP --> nForce MCP:   [5X]
nForce SPP c-- nForce MCP:   [5X]
**Spread Spectrum**
CPU Spread Spectrum: [Disabled]
HT Spread Spectrum: [Disabled]
PCle Spread Spectrurn(SPP): [Disabled]
PCle Spread Spectrurn(MCP): [Disabled]
SATA Spread Spectrum: [Disabled]
**FSB & Memorv Config**
FSB - Memory Clock Mode: [unlinked] (link)
FSB - Memory Ratio: (sync)
FSB (QDR), MHz: [AUTO] (1333)
Actual FSB (QDR), MHz: 1333
x MEM (DDR),  MHz: 1333 
Actual MEM (DDR), MHz: 1333
P1: auto
P2: auto
**Memory Timing Setting**
Memory Timing Setting: [expert] (manual)
tCL (CAS Latency): 9
tRCD: 9
tRP:  9
tRAS: 24
Command Per Clock: [2T]
** Advanced Memory Settings **
tRRD: [Auto] (5)
tRC: [Auto] (45)
tWR: [Auto] (12)
tWTR: [Auto] (18)
tFAW: [Auto] (39)
tREF: [Auto]  7.7uS (7.8uS)
tRFC: [Auto] (88)
**System Voltages** (manually set the System Voltages)
CPU Core: AUTO [1.18] (1.25v)
CPU FSB: AUTO [1.1] (1.20v)
Memory: AUTO[1.50v] (1.65v)
nForce SPP: AUTO[1.30] (1.30v)
nForce MCP: AUTO[1.500] (1.50v)
GTLVREF Lane 0: [Auto]  +00mv
GTLVREF Lane 1: [Auto] +00mv
GTLVREF Lane 2: [Auto]  +00mv
GTLVREF Lane 3: [Auto]  +00mv
**CPU Configuration**
Limit CPUlD Maxval: Disabled
Intel Speedstep: Disabled
xPPM Mode: [Native]
CPU Thermal Control: [Disabled]
C1E Enhanced Halt State: [Disabled]
Execute Disable Bit: [disabled]
Virtualization Technology: [Disabled]
CPU Core 0: [Enabled]
CPU Core 1: [Enabled]

norum
Ok! Just This? if it work I Try what?
If it not works?

Please try what I requested and let me know if it boots, and we will go from there.  Please enter all of the settings from the template in post #41, with only two of the RAM modules in the black slots (pick one of the two sets to use).

Why did you go from P08 to P10 and back to P08?

The pC is SHutDown with your Configs =/
 
But Is Stable for an half/hour. But I'm tried with 4 ram sticks.
 
So ?
 

Man!

I pass fast in my home, I will Try With TWO sticks.
I wanna your help.  I try with vcore,fsb,all of config, and I'll try
with 2 ram only. OK?
I will try, I didn't have a lot of time to do with much care.
 
I ask for patience because I'm have one pc at home.
And I'm at work. Weekend is coming and I will make the better to post
answers for my issue.
 
Thank you very much! Don't stay angry =))
 

norum

Yes! It's Run, I restart sometimes to put other things. HD, Coolers, Drive IDE, memory, and no failure, the red led function normal, just lit 2 times and the pc Loading normal, but when shutdown abnormal in the case the red light come lit and I can't get through the cycles. Just FF + lights or pc shut itself

 
Again I thinks its overheating. He says right here in red, when it shuts down the red LED is on. Either Overheating or CPU fried/installed wrong. Am I missing something? I don't think its a BIOS setting issue causing this. Am I wrong?

VistaHead

D.M.W.T

norum
Yes! It's Run, I restart sometimes to put other things. HD, Coolers, Drive IDE, memory, and no failure, the red led function normal, just lit 2 times and the pc Loading normal, but when shutdown abnormal in the case the red light come lit and I can't get through the cycles. Just FF + lights or pc shut itself

Again I thinks its overheating. He says right here in red, when it shuts down the red LED is on. Either Overheating or CPU fried/installed wrong. Am I missing something? I don't think its a BIOS setting issue causing this. Am I wrong?

I agree with you, and in one of my posts, I informed him that if the board runs out of the case, but not in the case, there is a case problem.  Right now, I am just trying to get him stable outside of the case, and then deal with that issue.

 
That makes sense, I think the language barrier is causing some issues. Have you seen grounding cause the red led to come on? I always assumed it just meant overheating/cpu isses. As far as settings go I am leaving it to you, it just kept bugging me that there is a hardware issue going on. lol.

I also cannot understand why hes using a cooler he cannot get to fit properly. 
 
To the OP: just be patient and listen to these guys if anyone can get you going its Vistahead and Jefferyham

norum
Well It's running in the case ^^
2mb with post 41 spec =.
It's hot, can I down the core voltage etc.
Calm down The temperature of cpu is 45 idle and cores are 51 and 53.
What I do Know?

What CPU cooler are you using?
Are you using the settings from post #41?
What is the ambient temperature of the room the PC is located in?
I would ask you to run a stress test, but if your CPU temps are in the mid-40's at idle, it would probably overheat while stress testing.  You may want to consider purchasing a better CPU cooling solution.
Please replace the two RAM modules that you are currently using with the other set that you have, and let us know if you have any problems using them.

Please post a BIOS template with the settings that you are currently using.  When you say it "shuts down", exactly what happens?  Does it freeze, as in the keyboard and mouse become unresponsive, or does it BSOD?  Bent socket pins would probably prevent it from posting at all, but I assumed you checked that when you mounted the stock cooler.  Overheating would cause a shutdown.  What are your temps when it shuts down?
Edit - You did not answer the following question:  What is the ambient room temperature of the room the PC is located in?